Dinan

Dinan Gloss Carbon Fiber Cold Air Intake - 2021-2024 BMW M2/M3/M4

Gloss Carbon Fiber - G80/G82/G83/G87

Material

Part # D760-0063 Be the first to write a review

Dinan Gloss Carbon Fiber Cold Air Intake - 2021-2024 BMW M2/M3/M4

In Stock
Free Shipping*
$1,639.95
Add to Wishlist
Starting at $145 a month with Learn More
7

Emissions

This part is legal under the provisions of EPA’s Tampering Policy dated November 23rd, 2020.

See Emissions Details
With the most potent BMW inline-6 to date, the S58, the newest iteration of the M3 has set itself apart from its predecessors; given the option for AWD, a model first, the M3 breaks boundaries long maintained by the quintessential brand icon. Being the signature chassis Dinan modifies, development on the G8x needed to similarly raise the bar and distinguish itself from the pack; a difficult task but one we relished the opportunity to embark upon. After months of comprehensive design and validation, that journey has come to its conclusion for the first of those ambitious aspirations - the Dinan G8x Carbon Fiber Cold Air Intake. Equal parts function, sound, and beauty, the intake not only looks and sounds the part of something special but performs the part as well. With a 12% increase in airflow to the engine without any negative effects on inlet temperatures or pressure, the Dinan G8x system delivers on all fronts. Drawing in more unimpeded air for consumption yields more efficient turbos (less work to make the same power) with the capacity for greater power potential on modified builds. Central to the design and our obsessive-compulsive need for a symmetrical engine bay is a singular plenum that replaces the separated driver and passenger intake ducting on the stock setup. The combination of the two tracks into one enlarged and distinctive shared pathway allows 50% more volume to be achieved in this tight space in addition to simplifying the installation and improving the overall look. The center plenum gives way to enlarged airboxes that house 11% larger cotton air filters delivering superb filtration while maximizing flow. Feeding the filters are the factory grill inlets as well as additional cutouts on the top of each airbox lid. The semi-open design was analyzed extensively to ensure that these additional inlets had no ill effect on temperatures or flow. However, the secondary airbox passages do allow an avenue for the induction soundtrack to escape the confines of its former plastic prison for everyone's benefit. Whether under hard acceleration, deceleration, or just spooling the amplified sounds are sure to make an impression. Beyond improvements to flow and sound, the appearance of the Dinan G8x M2/M3/M4 intake system is unrivaled. One need not do more than take a casual glance to know that care was taken with the system to blend in naturally with the factory engine bay while sufficiently augmenting it to a tier above. Playing off the hard angular edges that are present throughout, the Dinan intake system carefully takes these queues and carries them throughout for a true OEM+ look and feel. A 2x2 twill carbon fiber weave is used throughout and available in either gloss or matte - a first for Dinan, further setting the intake apart from those that came before.

Features:

  • Reduced intake restriction for Increased turbo efficiency with greater power potential on modified builds
  • More robust and aggressive induction soundtrack
  • Improved throttle response
  • More Flow: 12.4% increase over stock system (Stock: 815 CFM, Dinan: 916 CFM @ 28" H2O).
  • Larger volume air boxes (26% larger than stock) and tubes/plenum (50% larger than stock) allowing an increased volume of air to be utilized
  • 11% increase in filter area (stock: 65in², Dinan: 72in² per side) for optimum flow
  • Multiple finish options: Available in 2x2 Gloss or Matte Twill Carbon (Gloss Twill shown)
  • Bolt-on installation
Brand Dinan
Dinan Point Value3
Emission Code7
Labor Time (Hours)1.5
MaterialGloss Twill Carbon Fiber
Product TypeCold Air Intake
UPC810065214690
Part NumberD760-0063
7

This part is legal under the provisions of EPA’s Tampering Policy dated November 23rd, 2020. The company has reasonable basis (test results) to verify that this product allows the vehicle to operate within legal emissions standards and is therefore legal to be sold for on-street use in all states that accept the legal provisions of the Clean Air Act and the EPA Tampering Policy. This product is NOT LEGAL FOR SALE OR USE IN THE STATE OF CALIFORNIA. Testing with the California Air Resources Board, in order to achieve 50-state compliance, is pending with CARB. Once testing is complete with California, and an E.O. number is issued, this product will be updated to 50-state legal status.
OEM M4 CSL strut brace is not compatible with the Dinan intake.

Flow Bench Testing & CFD Analysis


The Dinan intake system outflows the factory setup by over 12% at 28" of H2O and averages 14% greater flow across all the tested scenarios. This translates into the ability to support higher power levels (ie: future-proofing the intake as a restriction to your future goals). The chart shown below is the summation of individual CFM measurements for both OEM driver and passenger intake tracts and in the case of the Dinan flow measurements, both boxes joined with the shared plenum. Utilizing a central plenum as opposed to two separate intake paths created a challenge in comparing the flow measurements of stock vs. Dinan on the bench but one that needed to be done to ensure the viability of the preferred symmetrical design. Numerous test sets to challenge and/or verify the data were used which included the following setups:


  1. 1 turbo inlet blocked with both filter sides open.
  2. 1 turbo inlet blocked with one filter inlet blocked.
  3. 1 turbo inlet blocked with the plenum blocked 2" past the opposite turbo inlet to as closely simulate the OEM individual pathways as possible.


With each successive test it became apparent that no matter the combination, the CFM measurement itself was largely unaffected by the shared plenum regardless of how much extra volume on the opposing side of the path was being utilized. In fact, between all 3 setups, the difference in CFM was within 2% across the entire range. Additional tables breaking down the individual driver and passenger banks are also supplied for those looking for more minute detail.


OEM DRVR.OEM DRVR.OEM DRVR.OEM PASS.OEM PASS.OEM PASS.OEM TOTAL
IN. H20MBARCFMIN. H20MBARCFMCFM
59721805973148328
1095925810961215473
2093337120937309680
2592042025925347767
2891244728918368815
3090646530913380845
4087954040889445985
DINAN DRVR.
DINAN DRVR.DINAN DRVR.DINAN PASS.
DINAN PASS.DINAN PASS.DINAN TOTAL
IN. H20MBARCFMIN. H20MBARCFMCFM
59732165973175391
1096030410961250554
2093542620938352778
2592147625925395871
2891550328918413916
3091052330914429952
40884606408905001106


In addition to flow bench testing, CFD analysis was also utilized to ensure the central plenum did not cause unnecessary turbulence that could cause a reduction in flow properties. The point where the 2 flow paths met within the shared pathway particularly was of great interest and under intense scrutiny. With some minor tweaks to the design the flow paths remained largely distinct from one another despite the shared space.


An OEM+ engine bay -- with options.

Central to Dinan's development process for decades has been the desire to create a cohesive package with parts working harmoniously with one another for a sum that is greater then its individual parts. Often this philosophy did not have to entertain aesthetics as parts were either hidden or did not come into contact with one another. With the G8x platform, this was not the case and afforded us the opportunity to express our creative side on an engine bay that had numerous visible parts interacting with one another. The intake and strut brace are the core of these modifications. Tying in stylistically with the OEM components, and playing off design cues from one another, the result is a breathtaking engine bay that is above reproach.


With the addition of a matte carbon option to both the intake and brace, there are also numerous combinations possible to express your unique style or carbon preference.

Reviews

    Your Review

    *Free Shipping & Handling only offered to the contiguous US on orders over $149, excludes clearance parts and oversized packages.

    Some parts are not legal for use in California or other states with similar regulations.